Table of Content
Slide six weights onto the weight guides with the pin grooves on the bottom. Push a weight tube bumper into the bottom of the short weight tube and push it through the center hole of the weight. Repeat this step with the holes on the right end of the weight base, but use 10 weights and the long weight tube. Bolt the butterfly seat frame and front leg together. Bolt the front leg to the butterfly base and the butterfly seat frame to the butterfly upright. Push caps into the top of the front leg and each end of the small leg lever.
Attach the bumper to the front of the front leg with a tap screw. Attach the small leg lever to the bracket on the front leg with a lubricated bolt and nylon jamnut that allows it to pivot freely. Locate the parts for the cable assembly. Bolt the 52-inch butterfly cable to the bracket on the left butterfly arm.
Weider Pro 9940 Home Gym User Manual - Newxl
Insert four 5/16” x 2 1/2” Carriage Bolts up through the indicated holes in the Press Base . Insert a 3/8” x 2 1/2” Carriage Bolt and a 3/8 x 4” Carriage Bolt up through the indicated holes at the end of the Press Base . Insert four 5/16” x 2 1/2” Carriage Bolts up through the indicated holes in the Butterfly Base .
Locate the parts for the seat assembly. Bolt the backrest to the butterfly upright and bolt the seat to the seat plate. Bolt this plate to the butterfly seat frame. Attach the seat on the press seat frame in the same way.
Weider Pro 9400 Support And Manuals
Locate and open the parts bag labeled “FRAME ASSEMBLY.” See drawing 1a. Press a 2” Square Inner Cap into each end of the Butterfly Base . Press two 2” Square Inner Caps into the Weight Base .
Attach the leg press plate to the leg press lever and secure the adjustment tube on top with a locking pin. Attach the curl pad with 2 bolts Add the deal then check all parts are properly tightened and all end caps are in place. Your Weider Pro 9940 is ready to use. Take a Pro pulley and wrap the press cable round it so the end with a ball is between the pulley and the welded pin on the press top fame. Take the threaded end round the existing pulley in the top frame and then take it down to the floor and round a 3 1/2-inch pulley.
Proform Xp 80 Bench – PFANBE1425.0 / PFANBE14250
Never release the press arms, butterfly arms, leg lever, lat bar or ab strap while weights are raised. The weights will fall with great force. Put the weight top frame across the top of both the uprights and bolt it on.
You will begin by assembling the base and the upright frames that serve as the skeleton of the equipment. Always disconnect the lat bar or ab strap from the home gym when performing an exercise that does not use the attachments. Missing weight bumpers on one side of the weights. The WEIDER 9940 offers a unique selection of weight stations designed to develop every major muscle group of the body. Keep the rest of the pulleys in the bag for future identification. It is approximately 52” long and it has a closed loop on each end.
Weider Pro 265 Ots Bench
A foam pad gives a measure of protection for vulnerable shins. The lower body workouts provide challenging routines for the hamstrings, quadriceps, and glutes. The Weider Pro 9940 is a home gym with a variety of weight stations designed to exercise all your major muscle groups.
Bolt this to a hole a few inches from the base of the press upright. Attach a pulley on the inside of the press frame and wrap the cable through. Take it through another pulley and attach it to the leg press lever. Lead it back to the upright and up to the top of the upright.
Top of the line home workout center. Plenty of weights and a variety of workouts. Breaks down into three parts for easy transportation or storage. Local delivery available for a small fee.
Trailer or lots of disassembly required.Missing weight bumpers on one side of the weights. Been using phonebook as bumper.Price $200 obo. Call, text, or email.Here is manual for gym ma ... The Weider Pro 9940 Home Gym is a brawny dual-station workout wonder. With two people able to work out at the same time, the Weider Pro 9940 Home Gym is a great family fitness machine. Everything in this manual is designed to ensure that our products can be assembled successfully by anyone.
Wrap the Press Cable around a 3 1/2” Pulley in the direction shown. Attach the Pulley and a Cable Trap to the indicated hole on the far side of the Leg Press Lever with a 3/8” x 4 3/4” Bolt and a 3/8”... Remove both 3 1/2” Pulleys from the pre-assem- bled Adjustable Pulley Plates . Attach the Pulley and a Cable Trap to the top hole in the two Adjustable Pulley Plates with a 3/8”... Place two Weight Bumpers over the indicated holes in the Weight Base .
No comments:
Post a Comment